Chainsaw won’t Start after Sitting- Find the Solution

Are you anxious about your most essential tools chainsaw? You probably think chainsaw won’t start after sitting when you are going to cut anything. Don’t worry about this. It is a common problem nowadays. A chainsaw may not run smoothly for many reasons.

Let’s talk about these common reasons that don’t start a chainsaw after sitting. And we also find out the solutions to fix it easily.

Why won’t you Start Chainsaw after Sitting?

Like many power tools, the chainsaw sometimes seems to get down. If you have gas-powered chainsaws, various things can go improper but fortunately, the maximum is easy to repair. Here are the most common reasons why your chainsaw may not start.

How to Check for Possible Problems

Whenever equipment of any kind breaks down, the correct way to identify the problem is to start with the most basic problems and remove each possibility one by one until the fault is found. Here, we try to focus on the most common tactics to relieve tension from the problem! So, get started to know the processes to start chainsaw.

When doesn’t get start a husqvarna chainsaw, you can do almost the same steps as below.

Solution-1: Check Its Fuel

Let’s get it out first. Does your chainsaw have gas in it? Yes? All right. The next one.

Solution-2: Check if It Contains New Fuel

Do you have fresh fuel in your chainsaw? Gasoline doesn’t last long, and if it stays inside your discipline for about a month, it will start to deteriorate. After that, some part of the liquid content will begin to evaporate, leaving sticky glue.

If you have old fuel inside your chainsaw, you need to remove it. Clean and clear the inner of the tank. Now add fresh gas, and start again.

Do you know the proper ratio?

The right measurement is 2.6 oz oil per 1 gallon gas 50:1 ratio.

Fuelling in the Chainsaw

Solution-3: Is the Carburetor Stuck?

Carburetor Stucking

The carburetor may be stuck. How? A stuck carburetor often leaves fuel in the chainsaw for a long time. Over time, some components of the fuel will evaporate, leaving a dense, sticky substance.

This sticky fuel can hold the carburetor and prevent the engine from starting. What do you do about that? If the carburetor is stuck, try to clean it with a carburetor cleaner.

If carburetor cleaning is not effective, rebuild or replace the entire carburetor.

Solution-4: Check the Spark Plug

The spark plug may be defective! What do you do then? When you detective the spark plug is not practical, discard the spark plug and replace it.

If the porcelain insulator is cracked, an electrode is burned or damaged, or the electron has a heavy carbon buildup, replace the spark plug.

Checking Spark Plug

Alternatively, if the spark plug has not been replaced in a few seasons, replace it.

When doesn’t get start a husqvarna chainsaw you can do the same steps like below.

Solution-5: Check the Air Filter

Can air filters stop the chainsaw? If the air filter is stuck or dirty, it will affect the gas ratio to air and prevent the engine from firing. If it does not start, check the air filter and clean it as needed.

You should also clean your air filter regularly as part of your general chain maintenance – and if it gets too dirty, you should replace it completely.

Solution-6: Check that the Engine is not Flooded

If you press the primer bulb too many times, you can flood the engine – a good indication of this is if you can smell the gasoline.

If you think you have a flooded engine, drain the fuel, push the choke back, and pull the starter cord 8-10 times while holding the throttle. Dry and clean the spark plug. If it is not working, buy a new one and turn it on again.

Solution-7: Chainsaw Ignition Coil

Chainsaw Ignition Coil

The ignition coil transmits voltage to the spark plug while the engine is running. If the ignition coil is inadequate, the engine will not launch. Before you replace the ignition coil, make sure the spark plug is in working condition.

If you are sure that the spark plug is not defective, check the ignition coil using an ignition coil tester. If the ignition coil is not working yet, replace it.

Solution-8: Spring Rewind

When the starter rope is pulled and released, the rewind spring removes the starry rope to a pulley. If the rewind spring breaks, the rope will not be able to return to the chainsaw pull.

As a result, starting the engine can be difficult or impossible. Replace it when the rewind spring breaks. It may be easier to replace the entire recoil starter assembly rather than many rewind springs replace individually.

Chainsaw Spring Rewind

Solution-9: Restore the Starter Assembly

If you have a problem with the recoil starter, pulling the starter cord will not turn the engine and therefore, it will not start. If the problem does not appear for any of the above reasons, it should be verified next.

To check, you need to remove the entire transfer starter assembly. The Recoil Starter Assembly employs a crankshaft to rotate the engine. If the recoil starter assembly is defective, the engine will not start and the chainsaw will not start.

Pulling the cord should cause the tabs to extend from the pulley and cam, the engine holding the hub and turning it. The tabs will then be withdrawn and the cord will have to be pulled again when you release the cord.

When you release the rope, the tabs should be withdrawn and the rope should be returned to the ley. If the recoil starter assembly does not work properly, replace it.

Solution-10: Blocked or Stuck Spark Ancestors

A spark receiver is a screen that prevents sparks from flying out of the china during use and it also affects the fuel-air mixture. With time and use, it can become blocked and needs to be cleaned regularly. If your saw has not started, it is advisable to check the spark arrestor’s condition to see if it needs to be cleaned.

Solution-11: Cold Weather

If the weather is too bad, it can make it challenging to start saws. If you have a cold somewhere and you have trouble with starting your chainsaw, try holding your breath a little further. This should help in most cases.

Chainsaw in Cold Weather

How do you Diagnose a Chainsaw Problem?

Problem-solving tips:

  • A chainsaw will not start. Make sure the switch is on and the choke is set correctly. 
  • The engine is moderate or idle installing. Adjust the carburetor by following the instructions in your owner’s manual.
  • There is no engine power. Remember, the chain brake is not engaging.
  • The engine smokes.
  • The chain does not move.
  • Chain clap.

What Causes a Chainsaw to Smoke?

It is not uncommon for chainsaws to be smoked, but if it does, it can result from excessive heating of the saws. A mixture of large amounts of oily fuels or the chain either not being sharp enough or not getting enough lubrication to create smoke.

In short, a smoking chainsaw is a sure sign that something is not right.

To give you better solution our worthy research

What would Cause a Chainsaw not to Start?

Not starting your saw can also result in dirty air filters. Garbage and dirty air filters will draw more gas than air, just like holding your breath. Saw running with stuck air filters increases the amount of carbon accumulated because it produces large amounts of burning fuel.

Final Verdict

See, we keep our words. Do we show all possible ways why a chainsaw won’t start after sitting? Of course, all of the above points only to gas-powered chainsaws. If you have battery-powered chainsaws or electronic chainsaws, there are very few that can go wrong.

If you are having trouble with starting one of these machines, the only advice is to check all obviously possible problems. Check that it is plugged into an outlet, including the cord chains, and that the power is on. With battery-powered models, make sure the battery is fully charged.

Outside of a simple check like this, if no such chainsaw is started, you may need to look into it with a professional.

Leave a Comment